DashBoard Part 4 and Bits

Its leather time , Was really dreading this part as it could go wrong very quick and is the focus point to the car .Started by laying the leather at the bottom and making sure that the bottom was going to fit
I glued the bottom in place and let it dry .
Next day came to the rest and started by stretching the leather up which seems to require 3 pairs of hands ,By good fortune had to leave for another task and came across a local furniture upholsterer,the conversation came round to my dash and a asked for any tips ,His reply was amazing ,bring it in and I'll do it for you. So I did and he only charged me beer money .

All my own work !!

   Another couple of little jobs tackled  was to blank off the two unused  ports on the engine .

Jubilee clip added to stop the cap falling off

Spare air box connection

This one I tapped with a 6mm tap and then stud locked a 6mm grub screw .

Also managed to finish off the heater pipes .

just grommets required

Undertray

On a recent visit to GD I noticed that one of the cars had a radiator protector fitted .
I thought it was a good idea so came home with one and the aluminium under tray. 

Ally under tray

the tray  fastens on the same bolts as the radiator so to save taking those out again I slotted the holes    when I came to try it in place it didn't fit (surprise) but because it fits in a tapper it was I case of take a bit off try it take a bit off try it etc .
the radiator protector was a similar story as in the laser cutting it warped and made marking it on to the top radiator bracket a challenge to say the least.

laser cut protector

Once in however it looks well worth the work .

The bottom is secured with 5mm bolts with washers to make up the difference but after twisting my sons arm he applied his lathe skills and made me some spacers !

Ah La Connor (thanks Son )

Dashboard Part 3

Next stage was to cut out the foam where the gauges need to be ,read other blogs and coped the idea of using a craft knife .This worked for the gauges but did not work for the switches or lights.
Came up with the idea of heating up a screwdriver and using it as a hot knife worked a treat .

dash hole cut including the additional hole for the heated seat 

Next thought I ought to look at the dash loom expecting it to have little labels on like the engine but no such luck .
Found myself looking at the build manual technical files and found the layout schematic and had to go though each plug and group of wires to identify them separately what a pain .

spaghetti with my masking tape idents  

This raised 2 issues  the first is there was no connection for the courtesy lights on the loom ( the wires just stopped at the plug ) .
the second was that there was a sender wire for the oil pressure  gauge but my gauge is pressure driven with an oil pipe .
Following the wire back though the looms it went to the unused wire at the back of the engine .

unused white oil pressure switch wire at top of picture

    I understand why there isn't an oil light as I have a gauge but .... if its there --  bought an adapter ring from ebay (£1.00) and then pestered my local motor dealers for an oil pressure switch to fit it ,result eventually and a huge thank you to Parkers (the parts people) ,switch that fitted  was from a Chevrolet Matiz( part number SOB807).

oil pressure take off with adaptor and pressure switch

   My idea now is to wire this in on the dash to the illumination on the start button ,my thinking behind this is when the ignition is on the start button will light up and go off when the engine starts .

Heater

Realised that after I had installed the heater there is another wire to go though the bulkhead to fasten on the battery It is the feed wire foe the ECU and fuel pump .
I was never totally happy with the heater pipe anyway as it seemed a bit tight in the hole and had the potential to wear though and empty the coolant so out it came to make the holes bigger .

Heater removed and holes made bigger

At the same time I noticed that the positive cable was not long enough to fit on the terminal and still look neat ,this was because I had routed it clear of the exhaust  .My solution was to fit a Battery isolating switch this comes with a removable key should I feel the need .


Battery switch fitted  and cable looks better

At the same time I thought it would be a good idea to have isolating valves on the heater circuit in case of a leak and also if I ever wanted the heater to blow cool air ( unlikely I know ) so ordered to valves from car builder solutions and happy with the fit.

the valves  have a flow arrow on so one is the wrong way round
which I will turn when I figure out which is the return pipe